Thanks to everyone that came out for Saturday's meeting.  As usual we covered a lot of territory.

We started with a discussion on Mission Models paint.  I've heard a great deal about these paints.  They've been very well received.  Here's a Link to their web site.  If you read the section under FAQ's you'll find how they believe you should spray their paints.  The manufacturer claims that their paint is a modern formulation.  At their site you can see their most current color offerings.  Interestingly they suggest that you only thin their paints by about 10%.  Although you can ready where they recommend thinning more.

Some basics about this paint.

• The paint comes in 1oz plastic bottles.  Thinner and Polyurethane additive comes in 2 oz plastic bottles.
• It is water based paint.  
• Because water based paints tend to be more fragile than lacquers, enamels, and non-water based acrylics, they recommend adding several drops of their polyurethane additive to increase durability.
• Like most paint manufacturers they recommend using their thinners.  That is a good call but if you don't have them use water.  Do not use windex, etc.
• Currently colors are designed for aircraft and armor.  However they offer a variety of colors that may be suitable for other subjects such as naval, space, etc.

John Miller from Model Paint Solutions recommends their paint and if you go to their site at this Link you'll see that they recommend painting much thinner.  As much as 80% to 90% for painting fine lines, 70% to 80% for modulation, and 60% to 70% for general painting.  John also recommends using a few drops of acrylic flow improver to keep the airbrush from clogging and to give the paint time to self level.  As mentioned before, John is writing a paper on his airbrushing at high altitudes.

I gave the paints a test with a fun subject, a B-17F Egg Plane.  This was a fun one.  I couldn't leave well enough alone.  I added 1/144 B-17F decals of the Memphis Belle (movie version) and also detailed the engines, bomb bay doors, nose antenna, bottom turret, and mast.  Sorry, I couldn't help myself. 😎

My experience here in Colorado with this paint was the following with this paint...

• If you thin at 80% to 90% for fine line painting (drawing fine lines with your airbrush), I couldn't dial the pressure back enough for it to atomize properly.  If I held the airbrush further away from the model it would dry off a little while airborne and work, but that defeats the purpose of fine line painting.  I used a .2 needle on my Harder and Steenbeck airbrush.  A 1.5 needle may delivery better results with heavily thinned paint.
• I found that 30% thinner worked pretty well on average.  Different colors may require slight differences in thinning.
• Building up layers in thin coats is recommended.
• Like Tamiya, Mission Models paint can be hand brushed.  
• I used Stynylrez primer and that worked well as a base coat.  I have not tried Mission Models primer yet.
• I found the paint leaves a very smooth finish when sprayed in thin layers.
• I recommend using the polyurethane additive to to improve the durability of the paint.
• I found that on the Stynylrez primer the paint DID NOT lift when removing masking tape.
• Mixing different colors works very well.  They offer basic colors so mixing a special color is easily accomplished.
• The clear finish I tried required more thinning.  When I sprayed it initially with only 10% thinner, it clogged rapidly on my airbrush needle and left a pebbly finish.  I have not tried hand brushing the clear coat yet.    
• Clean-up is very easy using the 50% denatured alcohol (window cleaning type found at Lowes) plus 50% Windex WITH Ammonia.  Also note that this cleaning mixture does a great job of cleaning Stynylrez primer from your airbrush.

Conclusions:  I think this is a very good paint to work with.  It is durable when using their Polyurethane additive and flows extremely well when adding a few drops of acrylic flow improver.  It cleans up easy.  It's a healthier product than enamels or lacquers.  It's reasonably priced and available at Colpar and online sellers.  Highly recommended if the colors and type of paint are right for you.

Next up, John DuGene gave a nice talk on the challenge he faced addressing a seam on corrugated material.  John ultimately used different sizes of sanding cord to restore the leading edge.  While not a nautical theme this is a material and technique that could be used in any type of modeling given similar challenges.  Excellent model John!

Sanding cords are traditionally used by woodworkers.  It comes in a variety of sizes.  The most common I found was from Mitchell Abrasives.  You can find it from the manufacturer, Rockler, or Amazon.  It comes in a variety of sizes and grits.  Here's a Link to the manufacturer's home page where you can learn about the different sizes and types available.   

Next under challenging circumstances, Bill Smallshaw gave a stellar presentation on Early Missile Cruisers.  Bill covered the three types of missiles and the ships they were attached to.  We received some excellent detail about the effectiveness of these systems.  Bill also did some excellent research and found kits of these subjects.  Sam Bartlett supported Bill by bringing in some of his kits, some of which were quite rare.  

Below are kits from NIKO models and the newest release from Blue Ridge Models of the USS Boston.  

The following is the list of kits from Bill's presentation covering this subject.  Thanks Bill for putting together this great presentation!  

§Revell

§USS Canberra CAG-2 1/480

§USS Boston CAG-1 1/480

§USS Long Beach CG-9 1/508

§USS Chicago CG-11 1/500

§Niko 1/700

§USS Canberra CAG-2 1967

§USS Springfield CLG-7 1970

§USS Galveston CLG-3 1968

§Jag 1/700

§USS Long Beach CG-9 1960s

§USS Albany CG-10

§Cyberhobby 1/700

§USS Long Beach CG-9  1980s

§USS Long Beach CG-9  1960s

§USS Albany CG-10

§Iron Shipwight 1/350

§USS Long Beach 1/350

§USS Albany 1/350

§Orange Hobby 1/350

§USS Boston CAG-1

§Jim Shirley 1/700

§USS Chicago CG-11

§Renewal 1/500

§USS Galveston 1/500

§USS Springfield CLG-7 1/500

Finishing off, Hugh Letterly brought in the model of the USS Shenandoah 1925 that he received from David Angelo, owner of Loose Cannon East.  This is the perfect companion piece to David's USS Patoka.  The Shenandoah is a resin kit available delivered for $55.  You can pick up the Patoka for $75 delivered.  David's web site is back up at this Link.  You can order directly from him.  Thanks for bringing this one in Hugh!  Very nice subject!  

  

Thanks everyone and we'll see you next time!